Cisco Systems Network Hardware 15454 User Manual

About this Manual  
Note  
The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms  
do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.  
Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's  
path protection feature, which may be used in any topological network configuration. Cisco does not  
recommend using its path protection feature in any particular topological network configuration.  
This section explains the objectives, intended audience, and organization of this publication and  
describes the conventions that convey instructions and other information.  
This section provides the following information:  
Revision History  
Date  
Notes  
March 2007  
April 2007  
Added the Revision History table.  
Changed fuse rating and power consumption specifications in Appendix A.  
Added note to indicate the support for LO circuits in SNCP in XC-VXC-10G  
card in the “Common Control Cards” chapter.  
May 2007  
Added OC48 IR/STM16 SH AS 1310 card information in the “Optical Cards”  
chapter and Appendix A.  
August 2007  
Updated the note in the SNCP Circuits section of the Circuits and Tunnels chapter.  
Cisco ONS 15454 SDH Reference Manual, R8.0  
August 2012  
xxxv  
 
 
Date  
Notes  
October 2008  
Updated the section “4.15.2 Ports and Line Rates” and “Table 4-17 Line Rate  
Configurations Per 15454_MRC-12 Port, Based on Available Bandwidth” in  
Chapter 4, Optical Cards.  
November 2008  
Updated the list of PM parameters for MRC-12 and MRC-4 cards in Chapter  
16, Performance Monitoring.  
Updated Server Trail section in Chapter 11, Circuits and Tunnels.  
Updated the section “Compatibility by Card” in the chapter, “Optical Cards”.  
January 2009  
March 2009  
Updated the SFP and XFP Card Compatibility table in Chapter 4, Optical Cards.  
Added a note in section “5.11 CE-MR-10 Card” of Chapter 5, Ethernet Cards.  
Updated the SFP and XFP Specifications table in Appendix A.  
Updated Figure 7-1 in Chapter 7, Card Protection.  
April 2009  
Updated the "TCC2P Card Specifications" section in Appendix A.  
Updated the Cisco ONS 15454 SDH bandwidth specifications section in  
“A.1.1 Bandwidth” of Appendix A, Hardware Specifications.  
Updated Table 11-13 and Table 11-14 in Chapter 11, Circuits and Tunnels.  
May 2009  
June 2009  
July 2009  
Updated the section “User Password, Login, and Access Policies” in Chapter  
9, Security.  
Updated “STM-N Speed Upgrades” in Chapter 12, SDH Topologies and  
Upgrades.  
Updated the table “PM Parameters for the STM-1 and STM1 SH 1310-8  
Cards” in Chapter 15, Performance Monitoring.  
Updated the section “CE-1000-4 Card” in Chapter 5, Ethernet Cards.  
Added a new section, Comparison of the Protection Schemes in the chapter,  
SDH Topologies and Upgrades.  
November 2009  
January 2010  
February 2010  
Updated the table “Line Rate Configurations Per 15454_MRC-12 Port, Based  
on Available Bandwidth” in the chapter, “Optical Cards”.  
Updated the section “STM-N Speed Upgrades” in the chapter SDH Topologies  
and Upgrades.  
Changed the BIEC parameter to BIT-EC in Chapter 15, “Performance  
Monitoring”.  
Updated the SFP/XFP Card Compatibility table for ADM-10G card in  
chapter Transponder and Muxponder Cards.  
April 2010  
Updated the section “SNMP Overview” in the chaper “SNMP”.  
August 2010  
Updated the section “Bridge and Roll” in the chapter “Circuits and Tunnels”.  
Removed the reference to G1000 card support in the chapters “Shelf and  
FMEC Hardware”, “Network Element Defaults”, “Performance Monitoring”,  
and “Ethernet Cards”.  
November 2010  
Updated the figure “ML1000-2 Faceplate and Block Diagram” under the section  
“ML1000-2 Card” in the chapter “Ethernet Cards”.  
Cisco ONS 15454 SDH Reference Manual, R8.0  
August 2012  
xxxvii  
 
Date  
Notes  
May 2011  
Updated the sections “Link Capacity Adjustment” and “VCAT Circuit Size”  
in the chapter “Circuits and Tunnels”.  
Updated the tables “ONS 15454 Card VCAT Circuit Rates and Members” and  
“ONS 15454 VCAT Card Capabilities” in the chapter “Circuits and Tunnels”.  
June 2011  
Updated the section “AIC-I Card” in the chapter “Common Control Cards”.  
January 2012  
Updated the privileges for the Download/Cancel operations in the table, "ONS  
15454 SDH Security Levels—Network View " in the chapter, “Security”.  
February 2012  
August 2012  
Updated the table “SFP and XFP Card Compatibility” in the chapter “Optical  
Cards”.  
The full length book-PDF was generated.  
Document Objectives  
This manual provides reference information for the Cisco ONS 15454 SDH.  
Audience  
To use this publication, you should be familiar with Cisco or equivalent optical transmission hardware  
and cabling, telecommunications hardware and cabling, electronic circuitry and wiring practices, and  
preferably have experience as a telecommunications technician.  
Related Documentation  
Use the Cisco ONS 15454 SDH Reference Manual with the following referenced publications:  
Cisco ONS 15454 SDH Procedure Guide, Release 8.0  
Provides procedures to install, turn up, provision, and maintain a Cisco ONS 15454 SDH node and  
network.  
Cisco ONS 15454 SDH Troubleshooting Guide, Release 8.0  
Provides general troubleshooting procedures, alarm description and troubleshooting procedures,  
error messages, and transient conditions.  
Cisco ONS 15454 SDH and Cisco ONS 15600 SDH TL1 Command Guide, Release 8.0  
Provides a full TL1 command and autonomous message set including parameters, AIDs, conditions  
and modifiers for the Cisco ONS 15454 SDH and Cisco ONS 15600 SDH.  
Cisco ONS 15454 SDH and Cisco ONS 15600 SDH TL1 Reference Guide, Release 8.0  
Provides general information, procedures, and errors for TL1 in the Cisco ONS 15454 SDH and  
Cisco ONS 15600 SDH.  
Cisco ONS 15454 and Cisco ONS 15454 SDH Ethernet Card Software Feature and Configuration  
G uide, Release 8.0  
Provides software features for all Ethernet cards and configuration information for Cisco IOS on  
Ethernet cards.  
Release Notes for the Cisco ONS 15454 SDH Release 8.0  
Provides caveats, closed issues, and new feature and functionality information.  
Cisco ONS 15454 SDH Reference Manual, R8.0  
August 2012  
xxxviii  
 
     
For an update on End-of-Life and End-of-Sale notices, refer to  
Document Conventions  
This publication uses the following conventions:  
Convention  
boldface  
italic  
Application  
Commands and keywords in body text.  
Command input that is supplied by the user.  
Keywords or arguments that appear within square brackets are optional.  
[
]
{ x | x | x }  
Ctrl  
A choice of keywords (represented by x) appears in braces separated by  
vertical bars. The user must select one.  
The control key. For example, where Ctrl + D is written, hold down the  
Control key while pressing the D key.  
screen font  
Examples of information displayed on the screen.  
boldface screen font  
Examples of information that the user must enter.  
<
>
Command parameters that must be replaced by module-specific codes.  
Note  
Means reader take note. Notes contain helpful suggestions or references to material not covered in the  
document.  
Caution  
Means reader be careful. In this situation, the user might do something that could result in equipment  
damage or loss of data.  
Cisco ONS 15454 SDH Reference Manual, R8.0  
August 2012  
xxxix  
 
 
Warning  
IMPORTANT SAFETY INSTRUCTIONS  
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you  
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar  
with standard practices for preventing accidents. Use the statement number provided at the end of  
each warning to locate its translation in the translated safety warnings that accompanied this  
device. Statement 1071  
SAVE THESE INSTRUCTIONS  
Waarschuwing  
BELANGRIJKE VEILIGHEIDSINSTRUCTIES  
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan  
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij  
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard  
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de  
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt  
raadplegen.  
BEWAAR DEZE INSTRUCTIES  
Varoitus  
TÄRKEITÄ TURVALLISUUSOHJEITA  
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin  
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu  
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen  
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien  
lausuntonumeroiden avulla.  
SÄILYTÄ NÄMÄ OHJEET  
Attention  
IMPORTANTES INFORMATIONS DE SÉCURITÉ  
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant  
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez  
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures  
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des  
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,  
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.  
CONSERVEZ CES INFORMATIONS  
WICHTIGE SICHERHEITSHINWEISE  
Warnung  
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen  
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und  
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder  
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten  
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.  
BEWAHREN SIE DIESE HINWEISE GUT AUF.  
Cisco ONS 15454 SDH Reference Manual, R8.0  
August 2012  
xl  
 
Avvertenza  
IMPORTANTI ISTRUZIONI SULLA SICUREZZA  
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle  
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli  
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.  
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le  
traduzioni delle avvertenze riportate in questo documento.  
CONSERVARE QUESTE ISTRUZIONI  
Advarsel  
VIKTIGE SIKKERHETSINSTRUKSJONER  
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du  
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med  
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten  
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne  
enheten.  
TA VARE PÅ DISSE INSTRUKSJONENE  
Aviso  
INSTRUÇÕES IMPORTANTES DE SEGURANÇA  
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de  
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos  
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de  
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para  
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.  
GUARDE ESTAS INSTRUÇÕES  
¡Advertencia!  
INSTRUCCIONES IMPORTANTES DE SEGURIDAD  
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular  
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los  
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el  
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña  
a este dispositivo.  
GUARDE ESTAS INSTRUCCIONES  
VIKTIGA SÄKERHETSANVISNINGAR  
Varning!  
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.  
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och  
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av  
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna  
anordning.  
SPARA DESSA ANVISNINGAR  
Cisco ONS 15454 SDH Reference Manual, R8.0  
August 2012  
xli  
 
Cisco ONS 15454 SDH Reference Manual, R8.0  
August 2012  
xlii  
 
Aviso  
INSTRUÇÕES IMPORTANTES DE SEGURANÇA  
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões  
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os  
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o  
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de  
segurança traduzidos que acompanham o dispositivo.  
GUARDE ESTAS INSTRUÇÕES  
Advarsel  
VIGTIGE SIKKERHEDSANVISNINGER  
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for  
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de  
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til  
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de  
oversatte advarsler, der fulgte med denne enhed.  
GEM DISSE ANVISNINGER  
Cisco ONS 15454 SDH Reference Manual, R8.0  
August 2012  
xliii  
 
Cisco ONS 15454 SDH Reference Manual, R8.0  
August 2012  
xliv  
 
Obtaining Optical Networking Information  
This section contains information that is specific to optical networking products. For information that  
pertains to all of Cisco, refer to the Obtaining Documentation and Submitting a Service Request section.  
Where to Find Safety and Warning Information  
For safety and warning information, refer to the Cisco Optical Transport Products Safety and  
Compliance Information document that accompanied the product. This publication describes the  
international agency compliance and safety information for the Cisco ONS 15454 system. It also  
includes translations of the safety warnings that appear in the ONS 15454 system documentation.  
Cisco Optical Networking Product Documentation CD-ROM  
Optical networking-related documentation, including Cisco ONS 15xxx product documentation, is  
available in a CD-ROM package that ships with your product. The Optical Networking Product  
Documentation CD-ROM is updated periodically and may be more current than printed documentation.  
Obtaining Documentation and Submitting a Service Request  
For information on obtaining documentation, submitting a service request, and gathering additional  
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and  
revised Cisco technical documentation, at:  
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS)  
feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds  
are a free service and Cisco currently supports RSS version 2.0.  
Cisco ONS 15454 SDH Reference Manual, R8.0  
August 2012  
xlv  
 
   
Cisco ONS 15454 SDH Reference Manual, R8.0  
August 2012  
xlvi  
 

Black Decker Automobile Accessories 90531551 User Manual
Black Decker Can Opener JW260 User Manual
Black Decker Drill KR50RE User Manual
Black Decker Sander 4040 User Manual
Blanco Indoor Furnishings 500 336 User Manual
Bogen Stereo System CG8A User Manual
Briggs Stratton Refrigerator 030222 User Manual
Cabletron Systems Cell Phone 9A656 04 ATM Module User Manual
Canon Printer 220 User Manual
Cisco Systems Musical Instrument Amplifier 15501 User Manual