Channel Plus Camcorder H721 User Manual

ChannelPlus Video Camera  
The H721 video cameras are solid state cameras designed to fit standard single gang  
Installing the Camera  
J-boxes. The H721 must be used with one of its companion channel injectors  
(H511HHR or H511BID). When used with an H511, video received from the  
H721 is used to create a new channel to add to existing television channels.  
The H721 is connected to the H511 by a single run of CAT-5 wire and does not  
need to be separately powered. The camera mount is weather-resistant and  
comes with a standard single-gang gasket. The brass cover-plate may be  
painted to match a house color.  
The H721 is designed to be mounted in a single-gang J-box using the supplied gasket.  
1
Two models are available:  
Model H721  
Black & White, 0.3 lux, 3.6 mm lens  
Model H721C  
Color, 6 lux, 3.6 mm lens  
Run a line of CAT-5 wire from the  
channel injector to the camera location.  
Standard  
single-gang  
J-box  
Note: The H721 is not a standalone video camera  
Use only with an H511 channel injector.  
Typical Installation  
Connect the H721 camera using only one method:  
1 Terminate cable with a CAT-5 jack and connect to the H511 using  
supplied RJ45 jumper. (Also see example H628 manual).  
J-box  
2 Wire camera or wall plate directly to the 8 position terminal block  
matching the CAT-5 wire colors to the colors on the terminal block.  
Insert wires and tighten screws.  
2
1
Prepare the CAT-5 wires by stripping  
1” of outer sheath and 1/8” of  
2
insulation. Insert wires into 8 position  
terminal block and tighten screws.  
Remember to wire through gasket.  
Program  
CAT-5 video  
CATV  
/Ant  
Output  
ower  
Channel Injector  
Power the H511 last -  
make all cable and  
CAT-5 connections first.  
H511HHR  
or  
H511BID  
Connect antenna or incoming  
cable to H511 input.  
3
Connect H511 output to splitter  
or distribution panel input.  
(See H511 manual)  
Push camera into J-box and attach  
using the two supplied screws.  
Maximum CAT-5 run:  
H721 to H511  
H721C to H511  
300 feet  
100 feet  
6-32 X 1”  
screw  
H721  
(rear view)  
Locating the Camera  
The camera ‘looks’ straight out from the cover-plate. For a front door application,  
place the camera lens 66 inches off the ground, adjacent to the door.  
Painting the Cover-Plate  
The brass cover-plate may be painted to match the house color. First, remove  
the camera from the plate. Lightly sand the plate using 300-400 grit wet/dry  
paper. Use a good quality metal primer that is rated for exterior use. Before  
applying the primer, follow the manufacturers instructions for cleaning the plate.  
Standard house paints may now be used.  
Insert wire into terminal block and tighten screws. Use the color bar to match  
wire colors. The color bar has two rows, one for CAT-5 and one for quad wire:  
- For CAT-5 wire, remove the default resistor and use all 8 wires.  
- For quad wire , leave default resistor in place and match four color wire.  
*
The H721/H721C was designed to work with CAT-5 wiring. Although the system will function with  
quad wire, CAT-5 delivers the highest quality picture. CAT-5 allows the use of an automatic line  
length sensor and picture compensator. Quad wire does not take advantage of this enhancement.  
*
DECLARATION OF CONFORMITY  
Specifications: typical @ 25OC 5OC  
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT  
TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL  
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE  
H721  
EIA (Black & White )  
H721C  
NTSC (Color)  
Model  
Image format  
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.  
Resolution, horizontal  
525 lines  
350 lines  
0.3 lux  
525 lines  
350 lines  
6 lux  
Installation requirements:  
Resolution  
FCC classifies this product under part 15 of its rules as a “television interface device”.  
Systems designed using television interface devices have the following legal requirements:  
1) The modulated channel signal strength may not exceed 15.56dBmV at any television.  
Federal Regulation 47CFR15.115(b)(1)(i).  
Minimum illumination  
Signal to Noise ratio  
>45 dB  
>45 dB  
2) If an antenna is used in the system, the modulated channel signal strength may not exceed  
-51dBmV at the antenna input port. Federal Regulation 47CFR15.115(c)(4).  
Yes  
Yes  
AGC  
3.6mm F2.0  
78O  
3.6mm F2.0  
78O  
Lens  
For the Installer:  
Lens viewing angle  
Any system you design must comply with these regulations. As the installer, you are  
responsible. The H721 or H721C (when used with an H511) has the necessary characteristics  
to comply with the above requirements as designed without additional accessories.  
The H511HHR is suitable for use with an antenna or with CATV systems.  
The H511BID is suitable for use with CATV systems only.  
automatic  
1/60 to 1/50000 second  
300 feet  
automatic  
1/60 to 1/50000 second  
100 feet  
White balance  
Electronic shutter speed  
Maximum distance to H511  
 

Belkin Mouse F8E820 PS2 User Manual
Black Box Switch 26615 User Manual
Blodgett Oven B36 RAD User Manual
Blue Coat Systems Time Clock Proxy SG User Manual
Bolens Lawn Mower 188 421 000 User Manual
Bosch Appliances Boiler R 29 HE User Manual
Bose Home Theater System AM352276 User Manual
Briggs Stratton Portable Generator 30324 User Manual
Casio Electronic Keyboard CTK 401 User Manual
Christie Digital Systems Projector LS+58 User Manual