Blue Sea Systems Battery Charger 7611 User Manual

Installation Instructions  
Mounting  
To avoid corrosion to connecting wires and terminals, mount in a dry and protected location  
if possible. Avoid locations directly above the battery banks.  
Marine Electrical Products  
BatteryLink® ACR  
Automatic Charging Relay  
with Auxiliary Battery Priority  
Electrical Connections  
• The wiring diagrams illustrated on the back page represent common installations and are not meant to  
be a guide for wiring a specific vehicle.  
PN 7611  
Features  
• The 7611 ACR is not intended to carry starting currents. Use a battery switching system with a  
combine batteries/parallel function if batteries may need to be combined for emergency starting.  
Caution: Disconnect battery connections before beginning the installation.  
• Automatically combines batteries during charging and isolates batteries when discharging  
• Optional Auxiliary Battery Priority connection shares the alternator charge with the Auxiliary battery  
longer allowing the use of the auxiliary loads for an extended period of time when the engine is running  
• 120A Continuous rating to support high output alternators  
Use the Wire Size and Fuse Ratings chart on page 2 to select the appropriate wire sizes to prevent  
overheating the ACR.  
• One tenth of the voltage drop of a battery isolator results in more fully charged batteries  
• Dual sensing to manage multiple charge sources  
• Robust, fully sealed assembly for reliability in environments with vibration and moisture  
• Clip-on cover insulates terminal connections  
Voltage Sensing  
The 7611 ACR will sense charging sources available on either battery bank.  
• Easy to install  
Minimum connections for operation:  
• Connect one battery bank to stud terminal A.  
• Connect the other battery bank to stud terminal B.  
• Integrated LED indicates ACR status (LED is ON when batteries are combined)  
• Optional remote LED output for indication of ACR status  
• Connect the quick connect terminal marked Ground to the DC system ground through  
a ten to fifteen amp in-line fuse to prevent fault currents from flowing in this wire.  
LED Status Chart  
LED  
ON  
Relay  
Closed  
Open  
Status  
Optional connections:  
1. Auxiliary Battery Priority  
Batteries Combined  
Batteries Isolated  
OFF  
The 7611 ACR can be configured to allow batteries to remain “paralleled” down to a decreased  
“Open Low” voltage of 12.25/24.5V DC if desired. Enable this feature if you need to access some of your  
engine start battery’s stored energy for accessory loads. The feature can be configured for temporary  
use while the ignition is on, or permanently. Wiring permanently allows this device to also be used as a  
Low Voltage Disconnect (LVD) to prevent accidental and potentially damaging over-discharge of  
accessory batteries by disconnecting loads.  
Specifications  
Continuous Rating  
Intermittent Rating (5 min.)  
Maximum Cable Size  
Terminal Stud Size  
12V DC  
120A  
210A  
1/0 AWG  
3/8"-16 (M10) 3/8"-16 (M10)  
140 in-lbs  
24V DC  
120A  
210A  
1/0 AWG  
To enable temporary voltage override:  
Connect a wire from the quick connect terminal marked Aux. Battery Priority through an  
appropriately sized in-line fuse (1A to 10A) to a terminal or wire running from the ignition switch  
that is +12/24V DC while the ignition is on, and at 0V DC when ignition is off.  
Maximum Torque  
Male Quick Connect Terminals 1/4x .032″  
140 in-lbs  
1/4x .032″  
Relay Contact Position  
To enable permanent voltage override:  
Combine  
Combine  
Open Low  
(30 sec.)  
(2 min.)  
(30 sec.)  
13.6V DC  
13.0 V DC  
12.75V DC  
16.0V DC  
27.2V DC  
26.0V DC  
25.5V DC  
32.0V DC  
Connect a wire from the quick connect terminal marked Aux. Battery Priority through an  
appropriately sized in-line fuse (1A to 10A) to a +12/24V DC source  
Open-Over Voltage Lockout  
2. Remote indicator lamp – mimics “COMBINED” LED on unit.  
Appropriate 12/24V LEDs include Blue Sea Systems PNs 8033 (amber), 8171 (red), or 8172 (green).  
Auxiliary Battery Priority  
Optional Feature  
To connect a remote LED indicator:  
Open Low  
(30 sec.)  
12.25V DC  
24.5V DC  
Connect the red wire of the LED to a 12/24V positive source through a 2A inline fuse.  
Connect the yellow wire of the LED to the quick connect terminal marked LED.  
Regulatory  
E marked for Ignition Protection, Meets ISO 8846,  
UL 1500 and SAE J1171 external ignition  
protection requirements  
Rated IP67----protected against immersion up to  
1 meter for 30 minutes  
Open/Close Cycling  
• If your electrical system is configured with a charging source that cannot supply the full load current  
being drawn from the receiving batteries, an open/close cycling process can occur. If this cycling  
continues, the second battery bank could eventually discharge even though a charge source  
is present.  
Guarantee  
Blue Sea Systems stands behind its products for  
as long as you own them. Find detailed  
For customer service, call 800-222-7617.  
980011740 Rev.002  
 

Belkin Network Card F5D6230 3 User Manual
Beyerdynamic Speaker System MCS D 200 User Manual
Bizfon Telephone Conference Series User Manual
Black Box Computer Accessories LTL EL User Manual
Blaupunkt Car Stereo System RDM 127 User Manual
Blomberg Washer WMF 8428 A User Manual
Bosch Appliances Blender MUM 4420 UC User Manual
BOXLIGHT Projector MP 38t User Manual
Canon Photo Printer iP5200 User Manual
Chief Manufacturing Stud Sensor CTA 225 User Manual