Blue Sea Systems Air Conditioner PN 8244 User Manual

Installation  
Installation  
Marine Electrical Products  
Marine Electrical Products  
Warning  
Warning  
Analog AC Voltmeter  
Analog AC Voltmeter  
It is not possible within the scope of these  
instructions to fully acquaint the installer  
with all the knowledge of electrical systems  
that may be necessary to correctly install  
this product. If the installer is not  
It is not possible within the scope of these  
instructions to fully acquaint the installer  
with all the knowledge of electrical systems  
that may be necessary to correctly install  
this product. If the installer is not  
0-150 Volts PN 8244 / PN 9353  
0-250 Volts PN 8245 / PN 9354  
0-150 Volts PN 8244 / PN 9353  
0-250 Volts PN 8245 / PN 9354  
Meter Specications  
Meter Specications  
knowledgeable in electrical systems we  
recommend that an electrical professional  
be retained to make the installation.  
knowledgeable in electrical systems we  
recommend that an electrical professional  
be retained to make the installation.  
PN  
Voltage  
PN  
Voltage  
Input Voltage:  
8244/9353 0-150 Volts AC  
8245/9354 0-250 Volts AC  
Input Voltage:  
8244/9353 0-150 Volts AC  
8245/9354 0-250 Volts AC  
Amperage Draw: 1 Milliampere  
Amperage Draw: 1 Milliampere  
1. Disconnect all AC and DC power  
Disconnect all AC power originating on or  
off the vessel. This includes inverters,  
generators, shore power attachments and  
any other device capable of supplying AC  
power to the ship’s circuits. Disconnect the  
main positive DC cable from all batteries to  
eliminate the possibility of a short circuit  
and to disable the inverter while installing  
the meter.  
1. Disconnect all AC and DC power  
Disconnect all AC power originating on or  
off the vessel. This includes inverters,  
generators, shore power attachments and  
any other device capable of supplying AC  
power to the ship’s circuits. Disconnect the  
main positive DC cable from all batteries to  
eliminate the possibility of a short circuit  
and to disable the inverter while installing  
the meter.  
Display:  
Analog scale  
Display:  
Analog scale  
Accuracy:  
3% of scale range  
Accuracy:  
3% of scale range  
PN  
Inches Millimeters  
PN  
Inches Millimeters  
Face Width:  
8244/8245  
2
50.80  
Face Width:  
8244/8245  
2
50.80  
9353/9354 2-5/8 66.70  
Mounting Hole: 8244/8245 1-1/2 38.10  
9353/9354 1-7/8 47.60  
9353/9354 2-5/8 66.70  
Mounting Hole: 8244/8245 1-1/2 38.10  
9353/9354 1-7/8 47.60  
Blue Sea Systems Inc.  
425 Sequoia Drive Bellingham, WA 98226 USA  
Phone (360) 738-8230 Fax (360) 734-4195  
Blue Sea Systems Inc.  
425 Sequoia Drive Bellingham, WA 98226 USA  
Phone (360) 738-8230 Fax (360) 734-4195  
Guarantee  
Guarantee  
Any Blue Sea Systems product with which  
a customer is not satised may be returned  
for a refund or replacement at any time.  
Any Blue Sea Systems product with which  
a customer is not satised may be returned  
for a refund or replacement at any time.  
9332 Rev. 003  
9332 Rev. 003  
(
(
Installation (continued)  
Installation (continued)  
2. Select mounting location and cut opening  
2. Select mounting location and cut opening  
Select a mounting location which is protected from water on the meter front and back and is not  
in an area where ammable vapors from propane, gasoline or lead acid batteries accumulate.  
The meter is not ignition protected and may ignite such vapors. There are two mounting  
methods for the meters, surface mount or panel mount.  
Select a mounting location which is protected from water on the meter front and back and is not  
in an area where ammable vapors from propane, gasoline or lead acid batteries accumulate.  
The meter is not ignition protected and may ignite such vapors. There are two mounting  
methods for the meters, surface mount or panel mount.  
Surface Mount: Drill ve clearance holes as shown below. The part number of the meter will  
determine the size and location of the clearance holes. Use the nuts and washers supplied in the  
accessory package to secure the four mounting studs to the mounting surface. This method will  
work on mounting surfaces up to 5/8” thick.  
Surface Mount: Drill ve clearance holes as shown below. The part number of the meter will  
determine the size and location of the clearance holes. Use the nuts and washers supplied in the  
accessory package to secure the four mounting studs to the mounting surface. This method will  
work on mounting surfaces up to 5/8” thick.  
PN 8244 / PN 8245  
PN 9353 / PN 9354  
PN 9353 / PN 9354  
PN 8244 / PN 8245  
Micro Meters  
Standard Meters  
Standard Meters  
Micro Meters  
Panel Mount: For thicker mounting surfaces, the meter can be mounted into a 0.125” thick  
panel. Blue Sea Systems offers meter mounting panels for our standard size meters only. Use  
PN 8013 to mount a single meter or PN 8014 to mount two meters.  
Panel Mount: For thicker mounting surfaces, the meter can be mounted into a 0.125” thick  
panel. Blue Sea Systems offers meter mounting panels for our standard size meters only. Use  
PN 8013 to mount a single meter or PN 8014 to mount two meters.  
 

Black Box Network Router ET0010A User Manual
Black Box Switch CATx User Manual
Bloomfield Coffeemaker 8372 User Manual
Bose Universal Remote BOSEPMC2 User Manual
Boss Audio Systems Car Speaker CE15DVC User Manual
Boss Audio Systems Car Stereo System 637UA User Manual
Braun Electric Shaver Series7 User Manual
Broan Bottle Warmer WPD29M User Manual
Broil King Food Warmer MLB CSLP4 User Manual
Casablanca Fan Company Fan 59123 User Manual