Perle Systems Network Card S 1110DP User Manual

Perle PoE/PoE+  
10/100/1000 Ethernet  
Media Converters  
Installation Guide  
S-1110P  
S-1110PP  
S-1110DP  
S-1110DPP  
P/N 5500317-11  
 
PoE (P)  
PoE+ (PP)  
Connector  
(xx)  
Mode  
Distance  
Wavelength  
(TX/RX)  
S-1110P-S1SC80U  
S-1110PP-S1SC80U  
SM  
80 km/50 mi.  
SC  
1510/1590 nm  
1590/1510 nm  
1550 nm  
S-1110P-S1SC80D  
S-1110PP-S1SC80D  
SM  
80 km/50 mi.  
SC  
S-1110P-S2xx120  
S-1110PP-S2xx120  
SM  
SC/ST  
SC  
120 km/74.6 mi.  
S-1110P-S1SC120U  
S-1110PP-S1SC120U  
SM  
1510/1590 nm  
1590/1510 nm  
1550 nm  
120 km/74.6 mi.  
S-1110P-S1SC120D  
S-1110PP-S1SC120D  
SM  
SC  
120 km/74.6 mi.  
S-1110P-S2xx160  
S-1110PP-S2xx160  
SM  
SC/ST  
SFP  
160 km/100 mi.  
S-1110P-SFP  
S-1110PP-SFP  
Note 1  
Note 1: Fiber characteristics will depend on the SFP fiber module  
selected.  
3 Port Models  
Dual Copper / PoE (DP)  
Connector  
Mode  
Distance  
Wavelength  
(TX/RX)  
Dual Copper / PoE+ (DPP) (xx)  
S-1110DP-M2xx05  
S-1110DPP-M2xx05  
MM  
550 m/1804 ft.  
SC/ST  
850 nm  
S-1110DP-S2xx10  
S-1110DPP-S2xx10  
SM  
10 km/6.2 mi.  
SC/ST  
SC  
1310 nm  
S-1110DP-S1SC10U  
S-1110DPP-S1SC10U  
SM  
10 km/6.2 mi.  
1310/1490 nm  
1490/1310 nm  
1310/1490 nm  
1490/1310 nm  
1310 nm  
S-1110DP-S1SC10D  
S-1110DPP-S1SC10D  
SM  
10 km/6.2 mi.  
SC  
S-1110DP-S1SC20U  
S-1110DPP-S1SC20U  
SM  
SC  
20 km/12.4 mi.  
S-1110DP-S1SC20D  
S-1110DPP-S1SC20D  
SM  
SC  
20 km/12.4 mi.  
S-1110DP-S2xx40  
S-1110DPP-S2xx40  
SM  
40 km/25 mi.  
SC/ST  
SC  
S-1110DP-S1SC40U  
S-1110DPP-S1SC40U  
SM  
40 km/25 mi.  
1310/1490 nm  
1490/1310 nm  
1550 nm  
S-1110DP-S1SC40D  
S-1110DPP-S1SC40D  
SM  
40 km/25 mi.  
SC  
S-1110DP-S2xx70  
S-1110DPP-S2xx70  
SM  
SC/ST  
SC  
70 km/43.5 mi.  
S-1110DP-S1SC80U  
S-1110DPP-S1SC80U  
SM  
80 km/50 mi.  
1510/1590 nm  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
3
 
Dual Copper / PoE (DP)  
Dual Copper / PoE+ (DPP) (xx)  
Connector  
Mode  
Distance  
Wavelength  
(TX/RX)  
S-1110DP-S1SC80D  
SC  
SM  
80 km/50 mi.  
1590/1510 nm  
1550 nm  
S-1110DPP-S1SC80D  
S-1110DP-S2xx120  
SM  
SC/ST  
S-1110DPP-S2xx120  
120 km/74.6 mi.  
S-1110DDP-S1SC120U  
S-1110DDPP-S1SC120U  
SM  
SC  
1510/1590 nm  
1590/1510 nm  
1550 nm  
120 km/74.6 mi.  
S-1110DP-S1SC120D  
S-1110DPP-S1SC120D  
SM  
SC  
120 km/74.6 mi.  
S-1110DP-S2xx160  
S-1110DPP-S2xx160  
SM  
SC/ST  
SFP  
160 km/100 mi.  
S-1110DP-SFP  
S-1110DPP-SFP  
Note 1  
3 Port Models - SPF  
Model  
PoE (P) / Dual SFP  
PoE+ (PP) / (Dual SFP)  
Connector  
(xx)  
Mode  
Distance  
Wavelength  
(TX/RX)  
S-1110P-DSFP  
SFP  
SFP  
Note 1.  
Note 1  
Note 1.  
Note 1.  
S-1110PP -DSFP  
4 Port Models - SFP  
Model  
Dual copper / PoE / Dual  
SFP  
Dual copper / PoE+/ Dual  
SFP  
Connector  
(xx)  
Mode  
Distance  
Wavelength  
(TX/RX)  
S-1110DP-DSFP  
SFP  
SFP  
Note 1.  
Note 1  
Note 1.  
Note 1.  
S-1110DPP-DSFP  
Note 1: Fiber characteristics will depend on the SFP fiber module  
selected.  
Please visit Perle’s website for the most up to date Installation  
guides models and specifications.  
4
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
Installation  
The default DIP switch settings (all switches in the UP position)  
will work for most installations.  
These are the steps required to configure the Perle S-1110P  
Ethernet media converter:  
1. Insert SFP Module (SFP Model only).  
2. Set the Auto-MDIX jumper setting (optional).  
3. Set the DIP switch settings (if required).  
4. Set the Powering Option Jumpers (if required).  
5. Install and connect the fiber cable(s).  
6. Install and connect the copper cable(s).  
7. Power up the media converter.  
Auto-MDIX Jumper Settings  
Note: The factory settings for Auto-MDIX will work for most  
installations, but in the rare case that you need to modify the  
settings, the procedure is below.  
For dual copper media converters, each copper interface has an  
Auto-MDIX jumper bank. To access the Auto-MDIX jumper  
settings, unscrew the six side screws on the case and remove the  
cover plate. Locate the MDIX AUTO jumper set as detailed below.  
By covering or strapping pins 1 and 2, the S-1110P will operate as  
an MDIX device. By covering or strapping pins 2 and 3, the S-  
1110P will automatically detect the Ethernet cable’s polarity.  
Removing the strapping is the same as AUTO.  
Note: The default jumper setting is AUTO  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
5
 
Power Sourcing Pinouts  
Note: The factory settings for Power Sourcing Pinouts will work for  
most installations as 802.3a and 802at-2009 ( POE/POE+)  
devices will detect and sync to the correct POE option. However,  
in the rare case that you need to modify the settings, the  
procedure is below.  
When Power Sourcing is enabled on a copper port, the S-1110P  
will provide power to the connected PD device over the Ethernet  
cable (see PSE function on Dip Switch configurations). The wire  
pairs on the cable used for delivering power will depend on the  
device. The following options are available.  
PoE Option  
RJ-45  
Alternative A  
Alternative B  
Legacy  
1
2
3
4
5
6
7
8
positive  
positive  
negative  
positive  
positive  
negative  
negative  
negative  
negative  
negative  
positive  
positive  
UTP (copper) Power  
PoE  
IEEE 802.3af (PoE) up to 15.4 Watts per UTP port.  
PoE+  
IEEE 802at-2009 (PoE+)  
Up to 30 Watts on a single UTP port model and up to  
25.5 Watts per port on a dual UTP port model  
PoE+ models will also support 802.3af PDs (Type 1)  
and PoE+ PDs (Type 2)  
6
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
Powering Options Jumper Settings  
In order to select a powering option, the Power Options Jumper  
settings must be set. Each copper port has a set of Power Option  
jumpers. To access the Powering Options Jumper settings,  
unscrew the six side screws on the case and remove the cover  
plate. Locate the Power Option jumper set and strap the option  
pins as detailed below.  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
7
 
DIP Switches  
The DIP switches are accessible through the opening in the side  
of the enclosure.  
Bank 1  
Bank 2  
Bank 1  
Bank 2  
Note: All switch changes take effect immediately. Switch changes  
will cycle power to the PD only if the PD Reset switch is set to On  
or you make changes to the PSE Power switches.  
8
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
DIP Switch Settings  
Bank 1  
Auto Negotiation copper (Switch 1)  
Switch Position Copper 1 Copper 2  
Up (default)  
Down  
Auto  
Off  
Auto  
Auto  
Note: Auto negotiation should only be turned off, if the copper link  
partner does not support Auto Negotiation and fixed settings are  
required by the copper link partner.  
Auto: When enabled, the media converter will negotiate with its  
link partner to determine the most optimal parameters for this  
connection. The S-1110P will advertise capabilities of 10,100 and  
1000 Mbps, full and half duplex as well as pause, and remote fault  
capabilities to the link partner.  
If the copper link partner does not support Auto negotiation, the S-  
1110P will parallel detect to 10 or 100 Mbps and force Half Duplex  
mode as per IEEE specifications.  
Off: When the Auto Negotiation switch is set to the OFF position,  
the media converter will not negotiate the Ethernet parameters  
with the copper link partner. The parameters used by the media  
converter will be determined by the Duplex (switch 4) and Speed  
(switch 5) DIP switch settings.  
Note: This switch affects the behaviour of copper port 1 only;  
copper port 2 is always set to Auto.  
Link Mode (Switch 2)  
Switch Position Mode  
Up (default)  
Down  
Standard Mode  
Smart Link Pass-Through  
Standard Mode: In this mode, link on the fiber and copper sides  
can be brought up and down independently of each other. A loss  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
9
 
of link on either the fiber or copper port can occur without affecting  
the other connection.  
Smart Link Pass-Through In this mode, the link state on one  
connection is directly reflected through the media converter to the  
other connection. If link is lost on one of the connections, then the  
other link will be brought down by the media converter.  
If the media converter has 2 copper or 2 fiber connections, then  
both must go down in order to affect the other connection(s).  
If the installation has a media converter on both ends of the fiber  
link and both are set-up for Smart Link Pass-Through, then a loss  
of copper link on the far end device will propagate through both  
media converters and will result in a loss of link at the near end  
device.  
Fiber Fault Alert (Switch 3)  
Switch Position Fiber Port 1 Fiber Port 2  
Up (default)  
Down  
Enabled  
Disabled  
Enabled  
Enabled  
Enabled: If the media converter detects a loss of signal on the  
fiber receiver, it will immediately disable its fiber transmitter signal  
on the same port. This, in effect, notifies the fiber link partner that  
an error condition exists on the fiber connection.  
If the remote media converter is set up for Fiber Fault Alert (FFA)  
and the local media converter is set up with Link Pass-Through, a  
loss of fiber link on either the transmit or receive line will be  
passed through to the local copper connection thus notifying the  
connected device.  
If the media converter has been set to Smart Link Pass-Through  
mode, the effect will be the same as FFA, since the link loss on  
the fiber receiver will result in bringing down the copper link, which  
will in turn cause the transmit fiber link to be brought down.  
Note: This feature only takes effect if Fiber Negotiation has been  
turned off.  
Disabled: The media converter will not monitor for or generate  
Fiber Fault Alert.  
10  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
Illustration of the FFA  
The following diagram is an illustration of the operation of this  
feature.  
(A) – Remote Media Converter setup for Fiber Fault Alert Enabled,  
Fiber Negotiation – OFF and Link Mode – Standard.  
(B) – Local Media Converter setup for Fiber Fault Alert Enabled,  
Smart Link Pass-Through On and Fiber Negotiation - OFF  
1 – (A) Loses fiber connection on its receiver.  
2 – (A) Sends FFA.  
3 – (B) Detects FFA signal and shuts down the fiber link.  
4 – (B) Drops link on copper connection because Smart Link  
Pass-Through is configured.  
5 – (A) Link on copper connection is not affected because Smart  
Link Mode is set to Standard.  
Duplex copper (Switch 4)  
Switch Position Copper port 1 Copper port 2  
Up (default)  
Down  
Full Duplex  
Half Duplex  
NA  
NA  
Note: When Auto Negotiation (SW1) is set to Off, the media  
converter will use this Duplex setting for copper port 1.  
Full Duplex: In the Up switch position; the media converter will be  
set to Full Duplex mode.  
Half Duplex: The media converter will be set to Half Duplex  
mode.  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter 11  
Installation Guide  
 
Speed copper (Switch 5)  
Switch Position Copper port 1 Copper port 2  
Up (default)  
Down  
100  
10  
NA  
NA  
Note When Auto Negotiation (SW1) is set to Off, the media  
converter will use this switch setting for copper port 1 speed.  
100: When Switch 5 is in the Up position, the S-1110P will force  
the speed to 100 Mbps.  
10: When Switch 5 is in the Down position the media converter will  
force the speed to 10 Mbps.  
Auto Fiber Negotiation (Switch 6)  
Switch  
Fiber 1  
Fiber 2  
Position  
1000 Mbps 1000 Mbps  
Up (default)  
Down  
Auto  
Off  
Auto  
Auto  
Auto: The Media Converter will negotiate Ethernet parameters on  
the fiber connection. This will ensure that the most optimal  
connection parameters will be in effect. If connecting to another  
Perle Media Converter, this parameter should be set to Auto. The  
Media Converter Module will advertise 1000Mbps, Full and Half  
Duplex, no Pause.  
Off: The Media Converter Module’s fiber will be fixed to  
1000Mbps, Full Duplex.  
Note: Fiber port 2 is always set to Auto.  
When using a 100 Mbps SFP module  
Full/Half Duplex on Fiber (Switch 6)  
Switch  
Fiber 1  
Fiber 2  
Position  
100 Mbps  
100 Mbps  
Up (default)  
Down  
Full Duplex Full Duplex  
Half Duplex Full Duplex  
12  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
Full Duplex: The Media Converter Module will be set to Full  
Duplex mode on its fiber link.  
Half Duplex: The Media Converter Module will be set to Half  
Duplex mode on its fiber link.  
Loopback Fiber-1 (Switch 7)  
Loopback Fiber-2 (Switch 8)  
Switch Position Mode  
Up (default)  
Down  
Disabled  
Enabled  
Disabled: The loopback feature is disabled. This is default  
position for normal operation. The switch must be set to this  
position in order for data to pass through the media converter.  
Enabled: This is a test mode. All data received on the receive  
(RX) fiber connection is looped back to the transmit (TX) fiber  
connection. The data link will be disabled; however power to the  
powered devices will be maintained. This mode will override all  
other switch settings.  
Note: On media converters with two fiber ports, both ports can be  
in loopback mode at the same time.  
Bank 2  
PSE Enable Copper-1 (Switch 1, 2)  
PSE Enable Copper-2 (Switch 4, 5) (dual  
copper models only)  
Switch Position 1, 4  
Switch Position 2, 5  
Type  
PSE enabled  
normal  
Up (default)  
Up (default)  
detection  
PSE enabled  
High  
capacitance  
detection  
Up  
Down  
PSE enabled  
Legacy device  
detection  
Down  
Up  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter 13  
Installation Guide  
 
Down  
Down  
PSE disabled  
These switches must be set in order to enable the power sourcing  
function and to indicate the type of device detection required. If the  
device type is unknown, the default should be used as per  
IEEE802.3af/at standards.  
Enabled: When enabled, the media converter will perform Power  
Sourcing Equipment (PSE) functions as per IEEE802.3af (POE) or  
802.3at-2009 (POE+) standards.  
Disabled: When disabled the media converter will not perform  
PSE functions.  
PD Power Reset 1 (Switch 3)  
PD Power Reset 2 (Switch 6) (dual copper  
models only)  
Switch Position Mode  
Up (default)  
Down  
Disabled  
Enabled  
Disabled: When disabled, the loss of fiber link has no effect on  
PSE power to the PD device.  
Enabled: When enabled, if the media converter detects loss of link  
on any fiber port it will turn off PSE output power to the PD device  
connected to copper port 1. After 2 seconds, the media converter  
will restore power to the PD and the power will remain on until one  
of the fiber links transitions from the link up to link down state.  
Disabled: When disabled the media converter will not perform  
PSE functions.  
14  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
Fiber Redundancy (Switch 7)  
Dual fiber models only  
Switch Position Mode  
Up (default)  
Down  
Disabled  
Enabled  
Disabled: When this feature is disabled, both fiber ports will  
operate as independent ports on a switch. Normal switch rules and  
functions will apply.  
Enabled: When this feature is enabled, fiber port 1 will be the  
primary active fiber connection port and fiber port 2 will be in  
standby and in an inactive state. Should a loss of link occur on  
fiber port 1, fiber port 2 will be activated within 50 ms. The MAC  
caching table for fiber port 2 will be cleared and the switch will  
begin to re-learn Mac address routing. See Redundant Primary for  
information on link connections.  
Redundant Primary (Switch 8)  
Note: This switch is used in conjunction with the Fiber  
Redundancy feature to determine the behaviour after link  
restoration.  
Switch Position Mode  
Up (default)  
Down  
Disabled  
Enabled  
Disabled: Following the loss of link on fiber port 1 and the  
activation of fiber port 2, fiber port 2 will remain the primary port  
until its link is lost at which time a switch over to fiber port 1 will  
occur.  
Enabled: Fiber port 1 will be designated as the Primary fiber port.  
If a loss of link occurs on fiber port 1 which causes a switch over to  
fiber port 2, the S-1110P will monitor fiber port 1 for link  
restoration. Once the link is re-established and remains so for 6  
seconds, fiber port 1 will be re-activated and fiber port 2 will be put  
back into stand-by-mode.  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter 15  
Installation Guide  
 
Installing the SFP Fiber Module  
SFP models only.  
1. Locate the appropriate fiber module and insert the SFP into  
the opening on the front of the media converter.  
2. Ensure the SFP module is properly seated. The release latch  
of the SPF fiber transceiver must be in the closed (up) position  
before insertion.  
3. The SFP module may be inserted before or after applying  
power to the media converter.  
4. Proceed with cable connections.  
Installing the Duplex Fiber Cable  
1. Locate a 1000Base-X compliant duplex (2 strands) fiber cable  
with appropriate connectors.  
2. Connect the fiber cables from one media converter to the  
other media converter/switch/fiber device ensuring that the RX  
and TX are reversed (crossed) at the opposite end.  
Installing the Simplex Fiber Cable  
1. Locate a 1000Base-X compliant simplex (1 strand) fiber cable  
with appropriate connectors. Ensure that the TX wavelength  
matches the RX wavelength at the other end and the RX  
wavelength matches the TX wavelength at the other end.  
2. Connect the fiber cable from one media converter to the other  
media converter/switch/fiber device.  
16  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
Installing the Copper Cable  
1. Locate 10/100/1000Base-T compliant copper cables with the  
appropriate connectors.  
2. Connect the RJ-45 cable between the Perle media converter  
and the device.  
Note: The Perle media converter supports Auto-MDIX which  
allows connection of a straight-through or cross-over Ethernet  
cable. See Auto-MDIX Jumper Settings in this guide for jumper  
positions.  
Grounding the Media Converter  
If your installation requires additional grounding the following  
procedure can be followed.  
Grounding the chassis requires the following items:  
One grounding lug (not provided).  
One 18 - 12 AWG wire (not provided).  
Cross-head screwdriver (not provided).  
Note: For your safety, when installing this equipment, always  
ensure that the chassis ground connection is installed first and  
disconnected last.  
Attaching the Grounding Lug  
1. Attach the grounding lug to one end of an 18-12 AWG wire.  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter 17  
Installation Guide  
 
2. Attach the grounding lug to the chassis and secure with the  
grounding screw(s).  
Attaching the Power cord strain relief clip  
1. Feed the power cord through the opening in the power cord  
relief clip.  
2. Attach the power cord relief clip to the chassis and secure with  
the provided screw.  
3. Plug the power cord into the AC power connector at the rear  
of the chassis.  
4. Plug the other end of the power cord into an appropriate  
power outlet.  
Powering up the Perle Media  
Converter  
1. Connect the Perle supplied power adapter to the media  
converter.  
2. Connect the power adapter to a power source.  
3. Check that the PWR LED light is lit.  
18  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
Operation  
Status LED  
The Perle PoE/PoE+10/100/1000 Rate converting Media  
converters have status LEDs located on the front panel of the unit.  
PWR  
On – Power is applied to the unit  
Blinking (slow) – Loopback mode (one or both fiber interfaces are in  
loopback mode)  
Blinking (fast) Power On failure. See LED Pattern to determine pattern  
combination and failure cause  
LED Pattern  
FDF LKF  
FDC PSE  
Off  
Off  
On  
On  
SFP incompatible  
Internal hardware  
failure  
All other LED patterns  
FDF-1/2 (Fiber 1/2 Duplex)  
On – Full Duplex  
Off – Half Duplex  
LKF-1/2 (Status on Fiber Link 1/2)  
On – Fiber link is present  
Off – No fiber link present  
Blinking (slow) – Fiber link appears functional – Fiber link has been  
brought down by Smart Link Pass-Through  
Blinking (fast) – Fiber link up and receiving data  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter 19  
Installation Guide  
 
SPD-(Copper Port 1/2)  
Green – 1000 Mbps  
Orange – 100 Mbps  
Off – 10 Mbps (if link is currently established)  
FDC-1/2 (Duplex on Copper 1/2)  
On – Full Duplex Mode  
Off – Half Duplex Mode  
LKC-1/2 (Link Status on Copper port 1/2)  
On – Copper link is present  
Off – No copper link present  
Blinking (slow) – Copper link appears functional – Copper link has  
been brought down by Smart Link Pass-Through.  
Blinking (fast) – Copper link up and receiving data  
PSE-1/2  
Solid Green (Active) – The PSE has successfully detected a compliant  
PD and is applying power over the UTP.  
Solid Orange (Inactive) – The PSE is not active. The PSE has been  
configured to provide power, however  
a compliant PD is not detected - no power applied  
a PSE has turned off power for Reset function  
Off – (Disabled) The PSE function is disabled in the configuration.  
Error conditions  
A blinking red light is an error condition. The led light will cycle  
with a 3 second stop interval between the error condition code.  
PSE-1 / 2 LED  
1 blink  
PD Capacitance too high  
2 blinks  
3 blinks  
PD Resistance too low or short circuit  
PD Resistance too high  
20  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
Other Features  
Auto-MDIX  
Auto-MDIX (automatic medium-dependent interface crossover)  
detects the signalling on the 10/100/1000BASE-T interface to  
determine the type of cable connected (straight-through or  
crossover) and automatically configures the connection.  
Pause (IEEE 802.3xy)  
Integrated Pause signalling is an IEEE feature that temporarily  
suspends data transmission between two devices in the event that  
one of the devices becomes overwhelmed with data. The Perle  
media converter can generate and respond to Pause messages. If  
Auto negotiation is set to On, the media converter will advertise  
symmetrical and asymmetrical pause. If Auto negotiation is set to  
Off, the Pause receive and send will be disabled.  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter 21  
Installation Guide  
 
Troubleshooting  
General  
1.  
Ensure power is supplied to the media converter. Only the  
Perle provided power supply may be used.  
2.  
Ensure the remote device’s fiber connection type is  
compatible with the media converter. If using a simplex  
fiber connection, ensure that you have both an Upstream  
(U) and Downstream (D) media converter.  
3.  
4.  
Ensure all cabling is of the correct type and is in good  
working order.  
For duplex fiber connections, ensure the RX and TX has  
been reversed between the two media converters.  
No connectivity  
If unable to get full connectivity with all DIP switches in the UP  
position, this procedure is recommended for troubleshooting.  
Method 1  
1. Set the Link Mode to Standard on both media converters.  
Leave all other switches in the Up position.  
2. Connect the copper device to the copper port on the media  
converter. The LKC LED light indicates good copper  
connection. If the LKC LED is not lit, the check the copper  
cable and the attached device.  
3. Repeat for the far end media converter.  
4. Connect the fiber cable to both media converters. The LKF  
LED indicates good fiber connection. If no LKF LED then  
check the fiber cabling. Ensure the transmitter and receiver  
pairs are crossed.  
5. Return the units to the desired configuration. Plug the other  
end of the power cord into an appropriate power outlet.  
Method 2:  
The fiber connection can also be verified by configuring the remote  
media converter for loopback mode. The LKF LEDs on both media  
converters should be lit. Data should pass through the local  
converter, over the fiber connection to the remote media  
22  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
converter. At the remote media converter, the data will be looped  
back and passed through the fiber, back to the local converter and  
passed to the copper link.  
No Power to the PD  
1.  
Ensure that the PD is compatible with the S-1110P. If the  
PD is a POE+ device, a POE+ media converter must be  
used. (S-1110PP)  
2.  
3.  
Ensure that the power supply being used, is the one  
provided with the product  
If the PD does not support Alternative A (including legacy  
PD’s), the Power Option Jumpers must be set accordingly.  
Also ensure the correct pin out for the device.  
4.  
For proper detection of different classes of devices, the  
dip switches must be set correctly.  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter 23  
Installation Guide  
 
Technical Specifications  
The following applies to all S-1110P media converters:  
Power Input / Consumption: 46V DC to 57V DC @ 6 W  
Operating Temperature:  
Storage Temperature:  
Operating Humidity:  
Storage Humidity:  
Operating Altitude:  
Dimensions:  
0°C to 50°C (32°F to 122°F)  
-25°C to 70°C (-13°F to 158°F)  
5% to 90% non-condensing  
5% to 95% non-condensing  
Up to 3,048 m (10,000 ft)  
150 mm by 95 mm by 26 mm  
MTBF  
1 copper port  
No Power  
supply  
POE  
POE+  
2 SFP / 1 copper ports  
1 SFP / 1 copper ports  
SC/ST – 1 copper ports  
399,432 hours  
410,188 hours  
361,190 hours  
218,384 hours  
221,560 hours  
206,434 hours  
79,977 hours  
80,399 hours  
78,317 hours  
MTBF  
2 copper ports  
No Power  
supply  
POE  
POE+  
2 SFP / 2 copper ports  
1 SFP / 2 copper ports  
SC/ST – 2 copper ports  
317,119 hours  
323,861 hours  
292,529 hours  
191,244 hours  
193,675 hours  
182,017 hours  
76,026 hours  
76,407 hours  
74,524 hours  
Fiber Optic Specifications:  
2 Port Models  
PoE (P)  
Wavelength  
(nm)  
TX Power  
(dB)  
RX Power  
(dB)  
Mode  
MM  
SM  
Budget  
7.5  
PoE+ (PP)  
S-1110P-M2xx05  
S-1110PP-M2xx05  
TX: 850  
RX: 850t.  
Min: -9.5  
Max: -4  
Min: -17  
Max: -3  
S-1110P-S2xx10  
S-1110PP-S2xx10  
TX: 1310  
RX: 1310.  
Min: -9.5  
Max: -3  
Min: -20  
Max: -3  
10.5  
24  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
PoE (P)  
PoE+ (PP)  
Wavelength  
(nm)  
TX Power  
(dB)  
RX Power  
(dB)  
Mode  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SFP  
Budget  
11  
S-1110P-S1SC10U  
S-1110PP-S1SC10U  
TX: 1310  
RX: 1490  
Min: -9  
Max: -3  
Min: -20  
Max: -3  
S-1110P-S1SC10D  
S-1110PP-S1SC10D  
TX: 1490  
RX: 1310  
Min: -9  
Max: 3  
Min: -20  
Max: -3  
11  
S-1110P-S1SC20U  
S-1110PP-S1SC20U  
TX: 1310  
RX: 1490  
Min: -8  
Max: -3  
Min: -22  
Max: -3  
14  
S-1110P-S1SC20D  
S-1110PP-S1SC20D  
TX: 1490  
RX: 1390  
Min: -8  
Max: -3  
Min: -22  
Max: -3  
14  
S-1110P-S2xx40  
S-1110PP-S2xx40  
TX: 1310  
RX: 1310.  
Min: -3  
Max: 5  
Min: -23  
Max: -3  
20  
S-1110P-S1SC40U  
S-1110PP-S1SC40U  
TX: 1310  
RX: 1490.  
Min: -3  
Max: 2  
Min: -23  
Max: -3  
14  
Min: -23  
Max:.-3  
Max: -3  
S-1110P-S1SC40D  
S-1110PP-S1SC40D  
TX: 1490  
RX: 1310  
Min: -2  
Max: -3  
14  
S-1110P-S2xx70  
S-1110PP-S2xx70  
TX: 1550  
RX: 1550  
Min: -2  
Max: 5  
Min: -23  
Max:.-3  
21  
S-1110P-S1SC80U  
S-1110PP-S1SC80U  
TX: 1510  
RX: 1590  
Min: -2  
Max: 3  
Min: -26  
Max:.-3  
24  
S-1110P-1SC80D  
S-1110PP-1SC80D  
TX: 1590  
RX: 1510  
Min: -2  
Max: 3  
Min: -26  
Max:.-3  
24  
S-1110P-S2xx120  
S-1110PP-S2xx120  
TX: 1550  
RX: 1550  
Min: -0  
Max: 5  
Min: -32  
Max: -3  
32  
S-1110P-S1SC120U  
S-1110PP-S1SC120U  
TX: 1590  
RX: 1510  
Min: -3  
Max: 2  
Min: -34  
Max:.-9  
31  
S-1110P-S1SC120D  
S-1110PP-S1SC120D  
TX: 1510  
RX: 1590  
Min: -3  
Max: 2  
Min: -34  
Max:.-9  
31  
S-1110P-S2xx160  
S-1110PP-S2xx160  
TX: 1550  
RX: 1550  
Min: 2  
Max: 5  
Min: -34  
Max:.-9  
31  
S-1110P-SFP  
S-1110PP-SFP  
Note 1  
Note 1  
Note 1  
Note  
Note 1: Fiber characteristics will depend on the SFP fiber module  
selected  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter 25  
Installation Guide  
 
3 Port Models  
Dual Copper / PoE  
(DP)  
Dual Copper / PoE+  
(DPP)  
Wavelength  
(nm)  
TX Power  
(dB)  
RX Power Budget  
Mode  
(dB)  
(dB)  
S-1110DP-M2xx05  
S-1110DPP-M2xx05  
TX: 850  
RX: 850  
Min: -9.5  
Max: -4  
Min: -17  
Max: -3  
MM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
SM  
7.5  
S-1110DP-S2xx10  
S-1110DPP-S2xx10  
TX: 1310  
RX:1310  
Min: -9.5  
Max: -3  
Min: -20  
Max: -3  
10.5  
11  
11  
14  
14  
20  
20  
20  
14  
14  
21  
23  
24  
24  
S-1110DP-S1SC10U  
S-1110DPP-S1SC10U  
TX: 1310  
RX:1490  
Min: -9  
Max: -3  
Min: -20  
Max: -3  
S-1110DP-S1SC10D  
S-1110DPP-S1SC10D  
TX:1490  
RX:1310  
Min: -9  
Max: -3  
Min: -20  
Max: -3  
S-1110DP-S1SC20U  
S-1110DPP-S1SC20U  
TX: 1310  
RX:1490  
Min: -8  
Max: -3  
Min: -22  
Max: -3  
S-1110DP-S1SC20D  
S-1110DPP-S1SC20D  
TX:1490  
RX:1310  
Min: -8  
Max: -3  
Min: -22  
Max: -3  
S-1110DP-S2SC40  
S-1110DPP-S2SC40  
TX: 1310  
RX:1310  
Min: -3  
Max: 5  
Min: -23  
Max: -3  
S-1110DP-S2ST40  
S-1110DPP-S2ST40  
TX: 1310  
RX:1310  
Min: -3  
Max: 5  
Min: -23  
Max: -3  
S-1110DP -S2LC40  
S-1110DPP -S2LC40  
TX: 1310  
RX:1310  
Min: -3  
Max: 2  
Min: -23  
Max: -3  
S-1110DP -S1SC40U  
S-1110DPP -S1SC40U  
TX: 1310  
RX:1490  
Min: -3  
Max: 2  
Min: -23  
Max: -3  
S-1110DP -S1SC40D  
S-1110DPP -S1SC40D  
TX:1490  
RX:1310  
Min: -2  
Max: -3  
Min: -23  
Max: -3  
S-1110DP -S2SC70  
S-1110DPP -S2SC70  
TX: 1550  
RX:1550  
Min: -2  
Max: 5  
Min: -23  
Max: -3  
S-1110DP -S2ST70  
S-1110DPP -S2ST70  
TX: 1550  
RX:1550  
Min:  
0
Min: -23  
Max: -3  
Max: 5  
S-1110DP -S1SC80U  
S-1110DPP -S1SC80U  
TX: 1510  
RX:1590  
Min: -2  
Max: 3  
Min: -26  
Max: -3  
S-1110DP -S1SC80D  
S-1110DPP -S1SC80D  
TX:1590  
RX:1510  
Min: -2  
Max: 3  
Min: -26  
Max: -3  
26  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
Dual Copper / PoE  
(DP)  
Dual Copper / PoE+  
(DPP)  
Wavelength  
(nm)  
TX Power  
(dB)  
RX Power Budget  
Mode  
(dB)  
(dB)  
S-1110DP -S2xx120  
S-1110DPP -S2xx120  
TX: 1550  
RX:1550  
Min: 0  
Max: 5  
Min: -32  
Max: -9  
SM  
SM  
SM  
SM  
SFP  
32  
S-1110DP -S1SC120U  
S-1110DPP -S1SC120U  
TX: 1590  
RX:1510  
Min: -3  
Max: 2  
Min: -34  
Max: -9  
31  
31  
32  
31  
S-1110DP -S1SC120D  
S-1110DPP -S1SC120D  
TX:1510  
RX:1590  
Min: -3  
Max: 2  
Min: -34  
Max: -9  
S-1110DP -S2xx160  
S-1110DPP -S2xx160  
TX: 1550  
RX:1550  
Min: 2  
Max: 5  
Min: -34  
Max: -9  
S-1110DP-SFP  
S-1110DPP-SFP  
Note 1  
Fiber Cabling Requirements:  
MM:  
50/125 microns or 62.5/125 microns  
SM:  
9/125 microns  
Ethernet Copper Cabling Requirements:  
Category 5 UTP or STP  
24-22 AWG  
Straight through or Ethernet crossover  
Note: Please refer the product page on the Perle website for the  
most up to date models and specifications.  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter 27  
Installation Guide  
 
Compliance Information  
FCC  
This product has been found to comply with the limits for a Class A digital device,  
pursuant to Part 15 of the FCC rules. These limits are designed to provide  
reasonable protection against harmful interference when the equipment is operated  
in a commercial environment. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in accordance with the  
instructions in this Guide, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful  
interference, in which case the user will be required to correct the interference at  
his/her own expense.  
EN 55022, Class A  
WARNING This is a Class A product. In a domestic environment this product may  
cause radio interference in which case the user may be required to take adequate  
measures.  
EN 55024, Class A  
Laser Safety – IEC 60825-1:2007  
This product meets Class I Laser safety requirements per IEC-60825-1:2007  
standard and complies with FDA/CDRH 21 CFR1040.10 and 21CFR1040.11.  
WARNING: Visible and invisible laser radiation may be present when cables are  
not connected. Do not stare into the beam or view the beam directly with optical  
instruments. Failure to observe this warning could result in an eye injury or  
blindness.  
WARNING: Use of controls, adjustments or the performance of procedures other  
than those specified herein may result in hazardous radiation exposure.  
28  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter  
Installation Guide  
 
Warranty / Registration  
Perle’s standard Lifetime Warranty provides customers with return  
to factory repairs for Perle products that fail under the conditions of  
the warranty coverage. Details can be found at:  
Contacting Technical Support  
Contact information for the Perle Technical Assistance Center  
(PTAC) can be found at the link below. A Technical Support Query  
may be made via this web page.  
Copyright  
© 2011 Perle Systems Limited  
All rights reserved. No part of this document may be reproduced or used in any form  
without written permission from Perle Systems.  
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter 29  
Installation Guide  
 

Pentax Digital Camera 15073 User Manual
Philips Computer Keyboard LFH2370 User Manual
Philips Cordless Telephone ID9372B User Manual
Philips DVR VR558 User Manual
Philips Headphones SHE4500 User Manual
Philips Stereo System FW 355C User Manual
Philips Work Light P 5775 B User Manual
PictureTel Webcam 760 User Manual
Polycom IP Phone 3725 26470 004 A User Manual
Poulan Lawn Mower 185491 User Manual