Omnitron Systems Technology Network Card Gx AN User Manual

from the power cable wires. Connect the power cables to the unit by fastening the  
stripped ends to the DC power connector.  
Connect the power wires to the DC power source. The Power LED should indicate  
the presence of power.  
iConverter Gx AN Standalone Module QUICK START GUIDE  
The Omnitron iConverter® Gx AN Standalone media converter provides 1000BASE-T  
WARNING: Note the wire colors used in making the positive and negative  
connections. Use the same color assignment for the connection at the DC  
power source.  
UTP to 1000BASE-FX fiber media conversion.  
The Gx AN can be used to connect Gigabit file  
servers to Gigabit switches and connect switches  
with Gigabit fiber uplinks.  
NOTE: If mounting with a safety ground attachment, use the safety ground  
screw at the rear of the unit.  
b. When using a Gx AN SFP model, insert the SFP Fiber transceiver into the Port 1  
SFP receptacle on the Gx AN.  
The GxAN supports Full/Half-duplex auto and forced  
negotiation with both hardware and software manual  
override controls.  
NOTE: The release latch of the SFP Fiber transceiver must be in the closed  
position before insertion.  
The Gx AN standalone module is an unmanaged device.  
c. Connect the UTP port via a Category 5 cable to a 1000BASE-T Ethernet device.  
For more information, including the complete User Manual on the Gx AN Standalone  
module, access Omnitron’s documentation download web page to view all relevant  
documents:  
d. Connect an appropriate multimode or single-mode fiber cable to the fiber port of  
the installed module. It is important to ensure that the transmit (TX) is attached to  
the receive side of the device at the other end and the receive (RX) is attached to  
the transmit side. Single-fiber (SF) media converter models operate in pairs. The  
TX wavelength must match the RX wavelength at the other end and the RX  
wavelength must match the TX wavelength at the other end.  
INSTALLATION PROCEDURE  
1) Configure DIP-Switches  
2) Set-up Module and Connect Cables  
3) Verify Operation  
3) VERIFY OPERATION  
Once the module has been installed and configured, per steps 1 and 2, verify the  
module is operational by viewing the status of the LED indicators. The table below  
provides a description for each LED indicator.  
1) CONFIGURE DIP-SWITCHES  
SW1 - Port 1 Auto/Manual Negotiation “AN MAN”  
The Power LED indicates the module is receiving power from the chassis.  
When this DIP-switch is in the Auto-Negotiate “AN” position (factory default), the fiber  
optic port is transparent to the network and allows the end devices connected to the  
module to advertise through the module and establish negotiated settings between  
the end devices. If Port 2 (UTP) is  
The Fiber Optic “FO” LED indicates the fiber optic connection between the modules  
has been established. Ablinking LED indicates the presence of data, an auto-negotiation  
problem or a link mode error indication.  
not connected, the fiber port will not  
be able to establish a fiber link. In  
The UTP LEDs indicate the module has established a connection across its UTP port.  
A blinking LED indicates the presence of data.  
the AN mode, the DIP-switches for  
LED Function  
Pause, Port 2 (UTP) and link  
modes RFD and SFD are ignored.  
Color  
Off State  
On / Blinking State  
On: Module has power  
"Legend"  
Power "Pwr"  
Green No power  
If two Gx AN modules are linked  
together and Port 1 is configured  
for auto-negotiation, the mode of  
operation will be determined by the  
devices connected to Port 2 (UTP).  
On: Fiber Link  
Fast Blinking: Fiber Data Activity  
1000Mbps  
Fiber Optics  
"P1"  
Green No Fiber Link  
Slow Blinking: Signal detect but  
auto-negotiation has not completed  
or SFD error detected  
Port 1 is transparent to the process.  
Figure A: DIP-Switch Location  
Half-Duplex when  
Green any UTP link is  
active  
Port 2 (UTP)  
Full-Duplex  
"FDX"  
On: Full-Duplex when any UTP link  
is active  
When this DIP-switch is in the  
Manual “MAN” position, the advertised values of Port 2 is controlled by DIP-switches  
SW2 through SW5.  
On: UTP linked at 1000Mbps  
Fast Blinking: UTP Data Activity  
Slow Blinking: SFD error detected  
Port 2 (UTP)  
1000Mbps  
"P2"  
Green Not linked  
SW2 and SW3 - Port 2 (UTP) Settings “AN MAN” “FDX HDX”  
These DIP-switches are only valid when Port 1 is set to “MAN”. Port 2 is always set to  
auto-negotiation and DIP-switches SW2 and SW3 only define what modes are  
advertised. See Figure C: Port 2 (UTP) Modes.  
Figure F: LED Indicators  
Form 040-8500N-002 A 9/07  
Omnitron Systems Technology * 140 Technology Dr. #500 * Irvine, CA 92618  
 

Miele Dishwasher G7859 User Manual
Milwaukee Glue Gun 2446 21XC User Manual
Milwaukee Saw 6177 59 User Manual
MRV Communications Stereo Amplifier EM316EDFA BR User Manual
MTD Lawn Mower PR DLSW User Manual
Optoma Technology Projector EH503 User Manual
Panasonic Cell Phone DMC TZ60 User Manual
Panasonic VCR AJ D960EG User Manual
Parkinson Cowan Cooktop U02021 User Manual
Patton electronic Doll 3086FR User Manual